[TV] Re: * RCA 35" No Horiz Scan
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[TV] Re: * RCA 35" No Horiz Scan
Tom, this is all I've got left on the trouble your having,but bare in mind
this is for a ctc177 but I think the chassis are close enough. if you have
not replaced these this can give problems with pin.cush. what i am listing
are part for ctc177 thay may be different in a ctc179. but the location
should be the same or close.
cr4403 will check good but replace it p/n 164589
c4402 p/n206007
cr4402 will check good but replace it p/n 242907
these might cause pin problems but not likely.
c4404 c4405 r2709 27k 1/2w
john
>From: <tom_rf@xxxxxxxxxxxxx>
>Reply-To: tv@xxxxxxxxxxxxxxx
>To: <tv@xxxxxxxxxxxxxxx>
>Subject: [TV] Re: * RCA 35" No Horiz Scan
>Date: Tue, 5 Apr 2005 20:18:24 -0500
>
>* Also source 28 listed as 7v is 25v on pins 5,6 into the second
>stage(high)...
>
>
>
>
>
>
>
>
>
>tom_rf@xxxxxxxxxxxxx
>
>----- Original Message -----
>From: <tom_rf@xxxxxxxxxxxxx>
>To: <tv@xxxxxxxxxxxxxxx>
>Sent: Tuesday, April 05, 2005 6:27 PM
>Subject: [TV] Re: * RCA 35" No Horiz Scan
>
>
> > * There is proper 3.5vout of the 1st stage pin1,but there is no output
>from
> > the comparator which is specified in a ctc203 schematic as 10v at pin 7
>no
> > drive to buffer transistor or driver and ultimately no 11 v out of
>driver
> > emitter.
> > The comp. chip has been replaced with the same results...
> >
> >
> >
> >
> >
> > tom_rf@xxxxxxxxxxxxx
> >
> > ----- Original Message -----
> > From: "Star-Tech" <STAR-TECH@xxxxxxxxxxxx>
> > To: <tv@xxxxxxxxxxxxxxx>
> > Cc: <star-tech@xxxxxxxxxxxx>
> > Sent: Tuesday, April 05, 2005 9:09 AM
> > Subject: [TV] Re: * RCA 35" No Horiz Scan
> >
> >
> > > Hello:
> > > The pin-out I have on a LM 311 shows pins 3 the
> > > invert input and pin 2 is the non-invert input. Also pin 8
> > > is the + VCC & pin 4 is the - VCC, with that in mind
> > > are you missing a voltage ?
> > > Greg Zumbro
> > >
> > > ----- Original Message -----
> > > From: <tom_rf@xxxxxxxxxxxxx>
> > > To: <tv@xxxxxxxxxxxxxxx>
> > > Sent: Monday, April 04, 2005 11:40 PM
> > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > >
> > >
> > > > I did not find any open resistors tracing out the circ.; However, My
> > > > comparator output pin 7, is suspect, being almost nothing, even when
> > > > grounding either comparator input pins 5, 6 (having 25.9v on both
>pins
> > > > high,but equal.
> > > > Output pin 7 not driving the input of the driver transistor,and
> > > consequently
> > > > no drive for the pin cush output transistor.
> > > > I will pickup a replacement comparator tomorrow, as it looks like it
>is
> > > the
> > > > problem componet for this part of the problem... but I am still open
>for
> > > > input until this beast has been tamed.
> > > >
> > > > Thanks again,
> > > >
> > > >
> > > >
> > > >
> > > > tom_rf@xxxxxxxxxxxxx
> > > >
> > > > ----- Original Message -----
> > > > From: <tom_rf@xxxxxxxxxxxxx>
> > > > To: <tv@xxxxxxxxxxxxxxx>
> > > > Sent: Monday, April 04, 2005 9:27 PM
> > > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > >
> > > >
> > > > > Yes, I have a LM311 8pin-dip comparator chip,also having a driver
>off
> > > of
> > > > > that and an output tranistor in the pin cushion circuitry area,
>before
> > > > > driving the yoke coil. I havent had a second over the weekend to
> > check
> > > > > voltages yet, but I will see if I can hunt down that fusable
>resistor
> > > that
> > > > > you have seen before...
> > > > >
> > > > > Thank you very much for
>your
> > > > input,
> > > > >
> > > > >
> > > > >
> > > > > tom_rf@xxxxxxxxxxxxx
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "Star-Tech" <STAR-TECH@xxxxxxxxxxxx>
> > > > > To: <tv@xxxxxxxxxxxxxxx>
> > > > > Cc: <star-tech@xxxxxxxxxxxx>
> > > > > Sent: Saturday, April 02, 2005 11:41 PM
> > > > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > >
> > > > >
> > > > > > Hello:
> > > > > > I still think you have lost control over the pincushing
> > > > > > circuit, not sure but do you have a stand up type board
> > > > > > near the H.O.T ? If so it has a dual op-amp ic, 8 pin IC, and a
> > > resistor
> > > > > > will open when you are missing
> > > > > > the horiz sweep.
> > > > > > Greg
>Zumbro
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: "J Sven2" <jsven2@xxxxxxxxx>
> > > > > > To: <tv@xxxxxxxxxxxxxxx>
> > > > > > Sent: Saturday, April 02, 2005 10:47 PM
> > > > > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > >
> > > > > >
> > > > > > > if you read down to the bottom of this email, it is
> > > > > > > listed in the original email. (CTC179dL)
> > > > > > >
> > > > > > > Thanks
> > > > > > >
> > > > > > > --- al m <ampm@xxxxxxx> wrote:
> > > > > > >
> > > > > > > > Chassis #?
> > > > > > > > Al Marquardt
> > > > > > > > ampm@xxxxxxx
> > > > > > > > Al Marquardt Electronic Repair
> > > > > > > > 206 W Main
> > > > > > > > Girardville Pa. 17935
> > > > > > > > ----- Original Message -----
> > > > > > > > From: <tom_rf@xxxxxxxxxxxxx>
> > > > > > > > To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > Sent: Thursday, March 31, 2005 12:05 AM
> > > > > > > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > >
> > > > > > > >
> > > > > > > > > the range ctls appear to be working in all but
> > > > > > > > pin/horiz width
> > > > > > > > > adjustments...by the way I am winging it w/out a
> > > > > > > > schematic, I might have
> > > > > > > > > to
> > > > > > > > > throw in the towel at some pt and download one.
> > > > > > > > >
> > > > > > > > > thanks,
> > > > > > > > >
> > > > > > > > > tom_rf@xxxxxxxxxxxxx
> > > > > > > > >
> > > > > > > > > ----- Original Message -----
> > > > > > > > > From: "Star-Tech" <STAR-TECH@xxxxxxxxxxxx>
> > > > > > > > > To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > > Cc: <star-tech@xxxxxxxxxxxx>
> > > > > > > > > Sent: Wednesday, March 30, 2005 10:07 PM
> > > > > > > > > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > > >
> > > > > > > > >
> > > > > > > > >> Hello:
> > > > > > > > >>
> > > > > > > > >> Do the numbers move in the horizonal
> > > > > > > > parameter
> > > > > > > > >> for the set-up service mode? Should be at 20 to
> > > > > > > > 22 for
> > > > > > > > >> width. If so you might find a shorted transistor
> > > > > > > > in the
> > > > > > > > >> pincushing circuit.
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > > Greg Zumbro
> > > > > > > > >> ----- Original Message -----
> > > > > > > > >> From: <tom_rf@xxxxxxxxxxxxx>
> > > > > > > > >> To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > >> Sent: Wednesday, March 30, 2005 10:05 PM
> > > > > > > > >> Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > > >> >
> > > > > > > > >> > Hey guys,
> > > > > > > > >> > I am finally replacing the parts
> > > > > > > > ordered, the two caps replaced
> > > > > > > > >> have
> > > > > > > > >> > restored the picture and is starting to look
> > > > > > > > like a TV again; However,
> > > > > > > > >> > I
> > > > > > > > >> > still have symptoms:
> > > > > > > > >> > 1.) Slight overscan, & there is
> > > > > > > > no WIDTH adjustment
> > > > > > > > >> > functionality in service mode "76".
> > > > > > > > >> > 2.) I have slight "pincushion"
> > > > > > > > warping upper /lower
> > > > > > > > > sides.
> > > > > > > > >> > 3.) Rear centering pot having
> > > > > > > > no effect on picture.
> > > > > > > > >> >
> > > > > > > > >> > upon looking, I found that I have left out
> > > > > > > > cr4408 which is missing. I
> > > > > > > > >> will
> > > > > > > > >> > p/u that diode tomorrow.
> > > > > > > > >> > *QUESTION: Will mssing CR4408 cause all these
> > > > > > > > symptoms?
> > > > > > > > >> >
> > > > > > > > >> > Thanks for your response,
> > > > > > > > >> >
> > > > > > > > >> > tom_rf@xxxxxxxxxxxxx
> > > > > > > > >> >
> > > > > > > > >> > ----- Original Message -----
> > > > > > > > >> > From: "John Conti" <contitv@xxxxxxxxxxx>
> > > > > > > > >> > To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > >> > Sent: Friday, February 25, 2005 9:54 AM
> > > > > > > > >> > Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > > >> >
> > > > > > > > >> >
> > > > > > > > >> > > Tom, c 4407 is a vertical yoke return cap if
> > > > > > > > open this will give you
> > > > > > > > >> > > a
> > > > > > > > >> > thin
> > > > > > > > >> > > vertical line the part number is 227315. the
> > > > > > > > part # for c4406 is
> > > > > > > > > 196050.
> > > > > > > > >> > and
> > > > > > > > >> > > for the diode cr4408 use part # 140971.
> > > > > > > > >> > > is the set fixed are is it still not. i dont
> > > > > > > > know if your looking for
> > > > > > > > >> > part#s
> > > > > > > > >> > > john
> > > > > > > > >> > >
> > > > > > > > >> > >
> > > > > > > > >> > >
> > > > > > > > >> > >
> > > > > > > > >From:
> > > > > > > > >> > > <tom_rf@xxxxxxxxxxxxx>
> > > > > > > > >> > > >Reply-To: tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > > >To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > >> > > >Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > > >> > > >Date: Thu, 24 Feb 2005 20:16:30 -0600
> > > > > > > > >> > > >
> > > > > > > > >> > > >I appreciate your reply,
> > > > > > > > >> > > >
> > > > > > > > >> > > > *TV Symptoms are no horiz. (Bright
> > > > > > > > Vertical line in the
> > > > > > > > > center
> > > > > > > > >> of
> > > > > > > > >> > > >the
> > > > > > > > >> > > >screen)
> > > > > > > > >> > > > To elaborate more on the prob
> > > > > > > > componets so far:
> > > > > > > > >> > > > * C4407 is labled
> > > > > > > > "S-Cap" and is a .67mic 250v
> > > > > > > > >> cap.
> > > > > > > > >> > > >(swollen)
> > > > > > > > >> > > > * C4406 is a . *2 mic
> > > > > > > > 80v electrolyt
> > > > > > > > >> (blown-like
> > > > > > > > >> > a
> > > > > > > > >> > > >firecracker)
> > > > > > > > >> > > > *They both have runs leading to
> > > > > > > > the back of the board
> > > > > > > > >> > leading
> > > > > > > > >> > > >to
> > > > > > > > >> > > >the horiz ctrg/ h lin. pots/ and C4407 is
> > > > > > > > >> > > > trace leads to horiz yoke wire.
> > > > > > > > (There are also other parts
> > > > > > > > >> labled
> > > > > > > > >> > > >"S-Cap" in functionality in this circ.
> > > > > > > > area.)
> > > > > > > > >> > > >
> > > > > > > > >> > > > There is a connecting
> > > > > > > > CR4408 to the smaller
> > > > > > > > >> voltage
> > > > > > > > >> > > >cap
> > > > > > > > >> > > >which may be suspect,
> > > > > > > > >> > > > (it's label is 51
> > > > > > > > 84408...2.0A Fast Recovery
> > > > > > > > >> > > >Rect.)checking good? (w/ 10Mohm diode chk).
> > > > > > > > >> > > >
> > > > > > > > >> > > >
> > > > > > > > >> > > >
> > > > > > > > >> > > >tom_rf@xxxxxxxxxxxxx
> > > > > > > > >> > > >
> > > > > > > > >> > > >----- Original Message -----
> > > > > > > > >> > > >From: "dek" <dek@xxxxxxxxxxxxxxx>
> > > > > > > > >> > > >To: <tv@xxxxxxxxxxxxxxx>
> > > > > > > > >> > > >Sent: Thursday, February 24, 2005 5:18 AM
> > > > > > > > >> > > >Subject: [TV] Re: * RCA 35" No Horiz Scan
> > > > > > > > >> > > >
> > > > > > > > >> > > >
> > > > > > > > >> > > > > Look for a diode in there that is the
> > > > > > > > equivalent of the 4118 in
> > > > > > > > > the
> > > > > > > > >> > 169,
> > > > > > > > >> > > > > but I forget what the actual number is.
> > > > > > > > Replace it, don't check
> > > > > > > > >> cause
> > > > > > > > >> > it
> > > > > > > > >> > > > > will check good.
> > > > > > > > >> > > > > Doug
> > > > > > > > >> > > > >
> > > > > > > > >> > > > > At 07:11 PM 2/23/05, you wrote:
> > > > > > > > >> > > > > >I am working on a 35" RCA CTC179dL
> > > > > > > > having no horiz scan,
> > > > > > > > >> > > >C407-electrolytic
> > > > > > > > >> > > > > >is blown apart, and C406 blue square cap
> > > > > > > > is swollen, butnot
> > > > > > > > >> checking
> > > > > > > > >> > > >shorted).
> > > > > > > > >> > > > > >If anyone has an excerpt from this
> > > > > > > > schematic, or have had this
> > > > > > > > > same
> > > > > > > > >> > > > > >particular componet problem it would be
> > > > > > > > apprec.
> > > > > > > > >> > > > > >
> > > > > > > > >> > > > > >
> > > > > > > > Thanks,
> > > > > > > > >> > > > > >
> > > > > > > > >> > > > > >tom_rf@xxxxxxxxxxxxx
> > > > > > > > >> > > > > >
> > > > > > > > >> > > > >
> > > > > > > > >> > > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > -
> > > > > > > > >> > > >----
> > > > > > > > >> > > > > >To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST
> > > > > > > > >> > > > > >email
> > > > > > > > >> > > > > >TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE
> > > > > > > > as the subject.
> > > > > > > > >> > > > > >Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > > > > >TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >> > > > >
> > > > > > > > >> > > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > -
> > > > > > > > >> > > >----
> > > > > > > > >> > > > > >
> > > > > > > > >> > > > >
> > > > > > > > >> > > > >
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > > > >> > > >-----
> > > > > > > > >> > > > > To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST email
> > > > > > > > >> > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as
> > > > > > > > the subject.
> > > > > > > > >> > > > > Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > > > > TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >> > > > >
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > > > >> > > >-----
> > > > > > > > >> > > > >
> > > > > > > > >> > > >
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > -
> > > > > > > > >> > ----
> > > > > > > > >> > > >To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST email
> > > > > > > > >> > > >TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as
> > > > > > > > the subject.
> > > > > > > > >> > > >Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > > >TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >>--------------------------------------------------------------------------
> > > > > > -
> > > > > > > > >> > ----
> > > > > > > > >> > > >
> > > > > > > > >> > >
> > > > > > > > >> > >
> > > > > > > >
> > > > > > >
>_________________________________________________________________
> > > > > > > > >> > > Is your PC infected? Get a FREE online
> > > > > > > > computer virus scan from
> > > > > > > > > McAfee®
> > > > > > > > >> > > Security.
> > > > > > > >
> > > > > > > http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > >> > -----
> > > > > > > > >> > > To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST email
> > > > > > > > >> > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the
> > > > > > > > subject.
> > > > > > > > >> > > Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > > TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > >> > -----
> > > > > > > > >> > >
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > >> -----
> > > > > > > > >> > To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST email
> > > > > > > > >> > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the
> > > > > > > > subject.
> > > > > > > > >> > Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> > TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > >> -----
> > > > > > > > >> >
> > > > > > > > >>
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > > -----
> > > > > > > > >> To remove yourself DO NOT Email
> > > > > > > > TV@xxxxxxxxxxxxxxx you MUST email
> > > > > > > > >> TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the
> > > > > > > > subject.
> > > > > > > > >> Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > >> TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >>
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > > > > -----
> > > > > > > > >>
> > > > > > > > >
> > > > > > > > >
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > -----
> > > > > > > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx
> > > > > > > > you MUST email
> > > > > > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the
> > > > > > > > subject.
> > > > > > > > > Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > > TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > > >
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > -----
> > > > > > > > >
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > -----
> > > > > > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx
> > > > > > > > you MUST email
> > > > > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the
> > > > > > > > subject.
> > > > > > > > Sent VIA Tech Assist's email server-
> > > > > > > > tv@xxxxxxxxxxxxxxx
> > > > > > > > TV email Archives at:
> > > > > > > > http://www.circuitwork.com/archive/TV/
> > > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > -----
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > __________________________________
> > > > > > > Do you Yahoo!?
> > > > > > > Yahoo! Personals - Better first dates. More second dates.
> > > > > > > http://personals.yahoo.com
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > > -----
> > > > > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST
>email
> > > > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > > > > > > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > > > > > > TV email Archives at: http://www.circuitwork.com/archive/TV/
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > >
> > > > > > -----
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > -----
> > > > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST
>email
> > > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > > > > > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > > > > > TV email Archives at: http://www.circuitwork.com/archive/TV/
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > > -----
> > > > > >
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > -----
> > > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
> > > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > > > > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > > > > TV email Archives at: http://www.circuitwork.com/archive/TV/
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > > -----
> > > > >
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > > -----
> > > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
> > > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > > > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > > > TV email Archives at: http://www.circuitwork.com/archive/TV/
> > >
> >
> >
>--------------------------------------------------------------------------
> > > -----
> > > >
> > >
> >
> >
>--------------------------------------------------------------------------
> > -----
> > > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
> > > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > > TV email Archives at: http://www.circuitwork.com/archive/TV/
> >
> >
>--------------------------------------------------------------------------
> > -----
> > >
> > >
> >
> >
>--------------------------------------------------------------------------
>-----
> > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
> > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> > Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
> > TV email Archives at: http://www.circuitwork.com/archive/TV/
> >
>--------------------------------------------------------------------------
>-----
> >
>
>-------------------------------------------------------------------------------
>To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
>TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
>Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
>TV email Archives at: http://www.circuitwork.com/archive/TV/
>-------------------------------------------------------------------------------
>
_________________________________________________________________
FREE pop-up blocking with the new MSN Toolbar ? get it now!
http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
-------------------------------------------------------------------------------
To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
Sent VIA Tech Assist's email server- tv@xxxxxxxxxxxxxxx
TV email Archives at: http://www.circuitwork.com/archive/TV/
-------------------------------------------------------------------------------