[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[TV] Re: RCA Model# 27F530T Chassis# M134C need wire location
Good Morning,
I checked the other brown wire and it goes from S1 to S1. I can't find
another G1 for this wire. There is two G2's and one G3 that I can find.
Max
Bailes Electronics
Rt.4 Box 57-A
Hurricane,WV. 25526
----- Original Message -----
From: <number6@xxxxxxx>
To: <tv@xxxxxxxxxxxxxxx>
Sent: Tuesday, August 01, 2006 11:57 PM
Subject: [TV] Re: RCA Model# 27F530T Chassis# M134C need wire location
>
> Hello,
>
> Look at other jumper wires and see what is labeled at each end.
> Maybe they say G1 on oth ends for one wire and g2 for different wire or
> something
> like that but I would think it would say W1 w2 etc.
> Good luck,
> Cy
> ----- Original Message -----
> From: " Bailes Electronics" <trustnhim5@xxxxxxxxxxx>
> To: <tv@xxxxxxxxxxxxxxx>
> Sent: Tuesday, August 01, 2006 10:19 PM
> Subject: [TV] Re: RCA Model# 27F530T Chassis# M134C need wire location
>
>
>>
>> Hello Cy,
>> > No one else has been in this set. It's to short to go to the CRT board.
>> > This wire is factory wiring and has G1 in a circle on the board. The
> trace
>> > it's soldered into traces back to pin 8 (ground) on the FBT. I know
>> > what
>> > G1 is on the CRT board. This board has G1 G2 G3 in circles on the
>> > mainboard. It comes up and shutsdown instantly.
>> Max
>>
>>
>> Bailes Electronics
>> Rt.4 Box 57-A
>> Hurricane,WV. 25526
>> ----- Original Message -----
>> From: <number6@xxxxxxx>
>> To: <tv@xxxxxxxxxxxxxxx>
>> Sent: Tuesday, August 01, 2006 10:06 PM
>> Subject: [TV] Re: RCA Model# 27F530T Chassis# M134C need wire location
>>
>>
>> >
>> > Hello,
>> > Was someone else working on it?
>> >
>> > What are the symtoms?
>> > Could it go to the CRT board somewhere?
>> > G1?
>> > Cy
>> >
>> > ----- Original Message -----
>> > From: " Bailes Electronics" <trustnhim5@xxxxxxxxxxx>
>> > To: <tv@xxxxxxxxxxxxxxx>
>> > Sent: Tuesday, August 01, 2006 8:35 PM
>> > Subject: [TV] RCA Model# 27F530T Chassis# M134C need wire location
>> >
>> >
>> >>
>> >> Hello,
>> >> This set has a jumper wire not soldered into the board. One end is
>> > soldered into location G1 on the FBT side of T401 and the other is
> loose.
>> > Print doesn't show this wire. Does anyone have this board in their shop
> to
>> > check the location of where to solder the other end of this wire? It's
>> > a
>> > brown wire about 10" long. Any help would be greatly appreciated.
>> >> Thanks
>> >> Max
>> >> Bailes Electronics
>> >> Rt.4 Box 57-A
>> >> Hurricane,WV. 25526
>>
>>> -------------------------------------------------------------------------
> -
>> > -----
>> >> To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
>> >> TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
>> >> TV email Archives at: http://www.circuitwork.com/archive/TV/
>> >> Join our Pro only site, with a Professional Only email list:
>> >> http://tech-assist.org/register.htm
>>
>>> -------------------------------------------------------------------------
> -
>> > -----
>> >> TV email Archives at: http://www.circuitwork.com/archive/TV.
>> >> ------------------------------------------------------
>> >>
>> >
>>
>> --------------------------------------------------------------------------
> -----
>> > To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
>> > TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
>> > TV email Archives at: http://www.circuitwork.com/archive/TV/
>> > Join our Pro only site, with a Professional Only email list:
>> > http://tech-assist.org/register.htm
>>
>> --------------------------------------------------------------------------
> -----
>> > TV email Archives at: http://www.circuitwork.com/archive/TV.
>> > ------------------------------------------------------
>> >
>> >
>> >
>> > --
>> > No virus found in this incoming message.
>> > Checked by AVG Free Edition.
>> > Version: 7.1.394 / Virus Database: 268.10.5/403 - Release Date:
> 7/28/2006
>> >
>>
>> --------------------------------------------------------------------------
> -----
>> To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
>> TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
>> TV email Archives at: http://www.circuitwork.com/archive/TV/
>> Join our Pro only site, with a Professional Only email list:
>> http://tech-assist.org/register.htm
>> --------------------------------------------------------------------------
> -----
>> TV email Archives at: http://www.circuitwork.com/archive/TV.
>> ------------------------------------------------------
>>
>
> -------------------------------------------------------------------------------
> To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
> TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
> TV email Archives at: http://www.circuitwork.com/archive/TV/
> Join our Pro only site, with a Professional Only email list:
> http://tech-assist.org/register.htm
> -------------------------------------------------------------------------------
> TV email Archives at: http://www.circuitwork.com/archive/TV.
> ------------------------------------------------------
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.5/403 - Release Date: 7/28/2006
>
-------------------------------------------------------------------------------
To remove yourself DO NOT Email TV@xxxxxxxxxxxxxxx you MUST email
TV-REQUEST@xxxxxxxxxxxxxxx with REMOVE as the subject.
TV email Archives at: http://www.circuitwork.com/archive/TV/
Join our Pro only site, with a Professional Only email list:
http://tech-assist.org/register.htm
-------------------------------------------------------------------------------
TV email Archives at: http://www.circuitwork.com/archive/TV.
------------------------------------------------------